Chapter 26: Antennas
Free practice questions on Antennas, chapter 26 of the SARL's Class A manual, for South Africa's Radio Amateur Examination (RAE). Every question has the right answer and an explanation. Sections covered:
- 26.1 Antennas and electromagnetic fields
- 26.2 The electromagnetic spectrum
- 26.3 Polarisation
- 26.4 The half-wave dipole
- 26.5 The quarter-wave vertical
- 26.6 The groundplane antenna
- 26.7 Short and long vertical antennas
- 26.8 Loop antennas
- 26.9 Folded dipole
- 26.10 Multi-element arrays
- 26.11 The Yagi
- 26.12 Reflector antennas
- 26.13 Antenna gain
- 26.14 Effective Isotropic Radiated Power
- 26.15 Efficiency
- 26.16 Directivity as opposed to gain
- 26.17 Other performance measures
- 26.18 Stacking
- 26.19 Feedlines
- 26.20 Standing-wave ratio
- 26.21 Baluns
- 26.22 Multiband antennas
- 26.23 The log-periodic array
- 26.24 Making practical antennas
-
Show answer
An alternating current flowing in its conductors
A changing current sets up a changing magnetic field, which creates a changing electric field, and so on: an electromagnetic wave. A steady direct current gives only a steady magnetic field, which does not radiate.
-
Show answer
An electric field and a magnetic field together
Each varying field sets up the other, so a radio wave is always an electric (E) and a magnetic (H) field travelling together; neither travels alone. No air is needed: radio waves cross empty space.
-
Show answer
A changing electric field
By induction, an alternating magnetic field sets up a changing electric field, which in turn sets up a changing magnetic field, and so on: together they form an electromagnetic wave. An alternating field cannot induce a steady one.
-
Show answer
6 m
λ = 300 ÷ F = 300 ÷ 50 = 6 m, with F in megahertz, which is why 50 MHz is called the 6 m band. Dividing F by 300 instead turns the formula upside down and gives 0,17 m.
Try it: Frequency ↔ Wavelength -
Show answer
Their frequency, and so their wavelength
All electromagnetic waves travel at the speed of light; only their frequency, and with it their wavelength, differs. That is why radio waves, especially at the higher frequencies, behave much like light.
-
Show answer
The wavelength gets shorter and the energy higher
Higher frequency means shorter wavelength (λ = 300 ÷ F) and higher energy, with gamma rays at one end of the spectrum and radio waves at the other. A longer wavelength goes with a lower frequency.
-
Show answer
All three are perpendicular to one another
The E and H fields cross at 90°, and both lie at 90° to the direction of travel. A wave never travels along its own electric field.
-
Show answer
Its electric field is horizontal
Polarisation is named after the orientation of the electric field. In a horizontally polarised wave travelling parallel to the ground the magnetic field is in fact vertical, at right angles to the electric field.
-
Show answer
The orientation of its radiating conductors
The electric field lines up with the conductors carrying the RF current, so horizontal elements give horizontal and vertical elements give vertical polarisation. Turning a beam to another compass bearing leaves it unchanged.
-
Show answer
Vertically
The legs are vertical, and the electric field follows the conductors, so the wave is vertically polarised. A horizontally polarised station would hear very little of it on a line-of-sight path.
-
Show answer
Very little, since the senses are opposite
Circular polarisation makes the orientation of the antennas unimportant, but both ends must use the same sense. With RHCP at one end and LHCP at the other, very little signal gets through.
-
Show answer
Very little, as the polarisations differ
A horizontally polarised antenna responds very poorly to vertically polarised waves, and vice versa, so on line-of-sight paths, typical of VHF and UHF, both stations should use the same polarisation.
-
Show answer
The source reinforces waves reflected from the ends
Waves reflected from the ends return to the feed point just as the source reverses, so each cycle builds them up; by R = V ÷ I, small voltage and large current mean low resistance. Wire resistance is a separate loss.
-
Show answer
It is radiated as radio waves
Radiation resistance is the apparent resistance caused by power leaving the antenna as radio waves; it is why a dipole’s feed point is not zero ohms. Reflected power is a different matter, caused by a mismatch.
-
Show answer
About 72 Ω
A half-wave dipole’s radiation resistance is about 72 Ω (often quoted as 73 Ω), close enough to match 50 Ω coax well. 36 Ω belongs to the quarter-wave vertical, which works as half a dipole.
-
Show answer
At the centre, where it is fed
Electrons move freely near the centre but can hardly move at the open ends, so the current peaks at the feed point and falls to almost nothing at the tips. The voltage does the opposite, peaking at the ends.
-
Show answer
They carry a high RF voltage
Current falls to almost nothing at an open end, and where current is low the voltage is high, so the tips of an antenna carry high RF voltages. The highest current flows at the centre.
Try it: Half-wave Dipole -
Show answer
The tips carry little current, so they radiate little
Radiation comes mainly from the high-current centre; the tips carry little current and add little, so they can be bent, folded or sloped down, as in an inverted V. The tips actually carry the highest voltage.
-
Show answer
Outgoing waves meeting waves reflected from the ends
Waves travel from the feed point to each open end, reflect and return; together they form a pattern whose current and voltage peaks stay fixed along the wire. Standing waves on a feedline, measured as SWR, come from mismatch.
-
Show answer
East and west, broadside to the wire
A dipole radiates most at right angles to its wire and least off its ends, giving a figure-8 (bi-directional) azimuth pattern. Over ground the end nulls fill in a little, but the ends stay much weaker.
Try it: Half-wave Dipole -
Show answer
Ground reflections break its elevation pattern into lobes
Direct and ground-reflected waves add or cancel, so the elevation pattern breaks into lobes: one each side at about 27° at ½λ, two (14° and 47°) at 1λ. Higher mounting gives more lobes, not fewer.
Try it: Half-wave Dipole -
Show answer
Mount it as high as possible
Raising a horizontal antenna lowers the angle of its lowest lobe, and low-angle radiation is what long-distance contacts need. Hence the manual’s rule for horizontally polarised antennas: the higher, the better.
Try it: Half-wave Dipole -
Show answer
About 36 Ω
A quarter-wave vertical behaves like half a dipole, with the ground supplying the missing half, so its radiation resistance is about 36 Ω. Ground losses usually make the measured feed resistance quite a bit higher.
Try it: Quarter-Wave Ground-Plane Vertical -
Show answer
A low-resistance RF ground connection
The vertical is half a dipole with the ground as its other half, so ground resistance turns power into heat. An ordinary earth rod is a poor RF ground: 75% or more of the power can be lost.
Try it: Radial & Site Planner -
Show answer
A circle, the same in every horizontal direction
A vertical radiates equally in every horizontal direction, so its azimuth pattern is a circle: it is omni-directional. The figure-8 pattern belongs to a horizontal dipole.
Try it: Quarter-Wave Ground-Plane Vertical -
Show answer
Pointing in opposite directions, their radiation cancels
The radials form the missing half of the dipole and do carry current, but they point in opposite directions, so their radiation cancels and only the vertical radiator’s remains. They are usually resonant quarter waves.
-
Show answer
Droop the radials downwards at about 45°
Drooping the radials raises the feed impedance, reaching about 50 Ω at around 45°, a good match for coax. Drooped right down to 90°, they turn the groundplane into a vertical dipole.
Try it: Quarter-Wave Ground-Plane Vertical -
Show answer
More and longer radials, well insulated from the ground
The radials replace a lossy earth return, so adding more of them, making them longer and insulating them from the ground all cut losses. Broadcasters have long been required to use 120 buried quarter-wave radials.
Try it: Radial & Site Planner -
Show answer
Capacitive, cancelled by an inductor in series
A dipole shorter than ½λ or a vertical shorter than ¼λ is capacitive, and an equal inductive reactance in series, a loading coil, cancels it. An antenna slightly too long is inductive and takes a series capacitor.
Try it: Quarter-Wave Ground-Plane Vertical -
Show answer
Centre loading is more efficient but harder to support
A coil at the centre of the element is electrically more efficient than one at the base, but the element must then carry its weight, which complicates the mechanical design. Base loading is simpler, not more efficient.
-
Show answer
Up to about 5/8 λ, they still give a good pattern
A longer vertical has a higher radiation resistance, helping against a poor ground, and its pattern stays good up to about 5/8 λ, hence the popular 5/8 λ mobile whips. Beyond that, performance deteriorates.
Try it: Quarter-Wave Ground-Plane Vertical -
Show answer
2,6 m
A full-wave loop is one wavelength round, so each side is ¼λ: 300 ÷ 28,5 ÷ 4 = 2,63 m, nearest 2,6 m. Making each side a half wave gives 5,3 m, a loop twice too big.
Try it: Full-wave Loop -
Show answer
About 130 Ω
With more wire radiating than a dipole, a one-wavelength loop has a somewhat higher radiation resistance, typically about 130 Ω, purely resistive at resonance. About 300 Ω is the folded dipole’s figure.
Try it: Full-wave Loop -
Show answer
Diagonal
The current peaks at the fed corner and at the opposite one, each flanked by a horizontal and a vertical wire, so the radiation is diagonally polarised. Fed in the middle of a horizontal side, the loop is horizontally polarised.
Try it: Full-wave Loop -
Show answer
About 300 Ω
Folding a full-wave loop flat into a dipole shape keeps the dipole’s pattern, but the adjacent wire transforms its impedance up to about 300 Ω. About 72 Ω is the ordinary half-wave dipole’s figure.
-
Show answer
Exactly the same shape
A folded dipole radiates exactly as a plain half-wave dipole does; only its feed impedance differs. The second conductor gives it no extra gain or directivity.
-
Show answer
A full-wave loop squashed flat
A folded dipole is a full-wave loop squashed flat until it looks like a dipole with a second conductor alongside, fed in the middle of one side. A dipole with folded-back tips is still an ordinary dipole.
-
Show answer
One that favours some directions over others
Directivity means favouring some directions at the expense of others; a dipole, favouring two, already has some. A rotator only changes where a beam points: the manual’s fixed wire Yagis and wire LPA are directional too.
-
Show answer
Along the line from A towards B
Waves from A reach B a quarter cycle later, just as B’s lagging current catches up, so they add towards B; waves from B reach A 180° out of phase and cancel, giving a cardioid aimed from A to B.
-
Show answer
Only some elements are fed; currents are induced in the rest
In a driven array every element is fed, in the right phase, through a phasing network. In a parasitic array only one or some elements are fed, and the driven element induces currents in the others, as in a Yagi.
Try it: Yagi Beam -
Show answer
A half-wave driven element with parasitic elements parallel to it
A Yagi has a driven half-wave element connected to the transmitter, plus parasitic elements, a reflector and usually directors, parallel to it. Feeding every element through a phasing network makes a driven array.
Try it: Yagi Beam -
Show answer
Straight, parallel elements in a horizontal plane
A Yagi’s elements are straight and parallel, and the electric field follows them, so a horizontally polarised Yagi has its elements in a horizontal plane. Standing them vertically gives vertical polarisation.
-
Show answer
A Yagi
Straight, parallel metal elements, one driven and the rest parasitic, make a Yagi, properly the Yagi-Uda array after its two inventors. In a driven array every element is fed.
Try it: Yagi Beam -
Show answer
Only one
A simple Yagi has a single driven element connected to the feedline; the reflector and directors are parasitic, with currents induced in them. Some complex Yagis have more than one driven element.
Try it: Yagi Beam -
Show answer
Slightly longer, on the side away from the directors
The reflector is a little longer than the driven element and sits on the side away from the wanted direction; the directors, in front, are somewhat shorter. Element lengths and spacings set the phasing that forms the beam.
Try it: Yagi Beam -
Show answer
A cubical quad
The cubical quad, usually just called a quad, is a parasitic array of quad-loop elements. A quagi combines quad loops with straight, dipole-type elements.
Try it: Cubical Quad Beam -
Show answer
They hear little from the sides and back
A Yagi concentrates its radiation in the wanted direction and, on receive, hears little from the sides and back, cutting interference. Amateurs mount them on rotators, typically from about 14 MHz upwards.
Try it: Yagi Beam -
Show answer
A beam antenna
A beam, such as a Yagi or a quad, favours one direction, strengthening signals from there and rejecting interference from elsewhere. A dipole favours two opposite directions; verticals and groundplanes favour none.
Try it: Yagi Beam -
Show answer
Two sets at right angles on one boom, fed together
One set of elements gives vertical polarisation and the other horizontal; fed together, they give circular polarisation, which rotates continuously. A single set tilted at 45° is still linearly polarised.
-
Show answer
A dish must be many wavelengths across to give gain
A dish has to measure many wavelengths across to give real gain, which below about 1 GHz means an impractically large structure; Yagis or arrays do better there. A simple dipole can feed a dish too, not only a horn.
-
Show answer
20 wavelengths
λ = 300 ÷ F = 300 ÷ 2 400 = 0,125 m, so 2,4 ÷ 0,125 = 19,2 wavelengths, nearest 20. Using the 1,2 m radius instead of the diameter gives about 10.
Try it: Frequency ↔ Wavelength -
Show answer
Aperture antennas
Reflector antennas are also called aperture antennas: the dish increases the effective aperture, the area from which the antenna gathers energy. Parasitic elements belong to arrays such as the Yagi.
-
Show answer
It focuses its power in its main direction
Antennas cannot amplify; gain shows how much more power an antenna puts out in its best direction than a reference antenna does in its best direction, which it achieves by concentrating its radiation.
Try it: ERP & EIRP -
Show answer
2,1 dBi
In its best direction a dipole puts out 2,1 dB more than an isotropic radiator (often quoted as 2,15 dB), so 0 dBd = 2,1 dBi. 0 dBi is the isotropic radiator itself.
Try it: ERP & EIRP -
Show answer
10,1 dBi
A dipole has 2,1 dBi, so add 2,1 dB to a dBd figure to get dBi: 8 + 2,1 = 10,1 dBi. Subtracting gives 5,9 dBi, the wrong way round, since dBi figures are the larger.
Try it: ERP & EIRP -
Show answer
As meaningless until its reference is stated
A gain in decibels is a ratio to some reference antenna; without the reference, dBi or dBd, it means nothing. Published gain figures are also often inflated, so treat them with suspicion.
Try it: ERP & EIRP -
Show answer
About ten times as much
Antennas are reciprocal, working the same way on receive as on transmit, so 10 dBd means ten times the power from that direction. The bigger benefit on receive is hearing less noise from other directions.
Try it: dBm, Watts & dB -
Show answer
An ideal antenna radiating equally in all directions, up and down
An isotropic radiator sends equal power in all directions, including up and down; it cannot be built but is easy to calculate, giving the dBi reference. A vertical radiates equally only in horizontal directions.
-
Show answer
150 W
EIRP = P × G, with G as a ratio over an isotropic radiator: 7 dBi is a power ratio of 5, so 30 × 5 = 150 W. Adding 7 to 30 W mixes decibels with watts.
Try it: ERP & EIRP -
Show answer
20 W
A gain of 6 dBd is a power ratio of 4 over a dipole, so the Yagi needs only 80 ÷ 4 = 20 W for the same signal. Multiplying by 4 instead gives 320 W, the wrong way round.
Try it: ERP & EIRP -
Show answer
250 W
EIRP needs the gain over an isotropic radiator: 7,9 dBd + 2,1 dB = 10 dBi = 10 times, so 25 × 10 = 250 W. Using the dBd figure gives 154 W, the ERP, which is relative to a dipole.
Try it: ERP & EIRP -
Show answer
75%
Efficiency = power radiated ÷ power supplied = 90 ÷ 120 = 0,75 = 75%. The other 30 W, 25%, becomes heat in the elements and the ground; 133% turns the ratio upside down.
-
Show answer
60%
The feed resistance is 24 + 16 = 40 Ω, and only the radiation resistance’s share is radiated: 24 ÷ 40 = 60%. The 40% is the share lost as heat in the earth system.
-
Show answer
Its radiation resistance falls, but its losses do not
Shortening an element makes its radiation resistance drop rapidly while losses stay roughly constant, so a bigger share of the power becomes heat. A loading coil, adding loss resistance of its own, can make it worse.
Try it: Quarter-Wave Ground-Plane Vertical -
Show answer
The Beverage receiving antenna
A Beverage is very directional, which greatly improves reception against atmospheric noise, but it is so lossy that it suits transmitting only in special cases. A good Yagi has both directivity and gain.
-
Show answer
A lossy antenna can be very directional yet have little gain
Gain is directivity less losses: high-resistance wire or an inefficient feeder can waste much of the power, so a very directional antenna may show only modest gain.
-
Show answer
Its directivity improves reception against atmospheric noise
The Beverage’s great directivity rejects atmospheric noise arriving from unwanted directions, much improving reception, even though its heavy losses leave it little gain. Gain is not what it offers.
-
Show answer
23 dB
F/B is the forward level minus the rear level: 9 − (−14) = 23 dB, just as the manual’s +10 and −17 dB give 27 dB. Dropping the minus sign, 9 − 14 gives the wrong 5 dB.
-
Show answer
The angle between its half-power points
Beamwidth is usually measured between the half-power (−3 dB) points either side of the main lobe; the manual’s example has about 20° on each side, 40° in all. The null-to-null width is much wider.
-
Show answer
A clean pattern: narrow, with good F/B and low sidelobes
With strong signals but plenty of interference, a clean pattern that rejects unwanted directions counts for more than gain. Gain matters most for ultra-weak signals on a clear frequency.
-
Show answer
Stack it with a second, identical Yagi
Stacking identical antennas, all pointing the same way and fed together, narrows the beam and adds gain; some EME stations stack 32 or more Yagis. A Yagi pointing the other way adds nothing in the wanted direction.
-
Show answer
The vertical beamwidth narrows; the horizontal stays the same
Vertical stacking narrows the beam in the vertical plane while keeping the horizontal beamwidth; side-by-side stacking does the reverse. Stacking also tends to worsen F/B and sidelobe suppression.
-
Show answer
About 3 dB
Two antennas have twice the capture area, so at best twice the power, 3 dB, goes in the wanted direction; real arrays get a little less. Claiming 6 dB would need four times the power.
Try it: dBm, Watts & dB -
Show answer
1,4 m
In free space λ = 300 ÷ 145 = 2,07 m; in the cable it is shorter by the velocity factor: 2,07 × 0,66 = 1,37 m, nearest 1,4 m. Dividing by 0,66 gives 3,1 m, longer instead of shorter.
Try it: Feedline Electrical Length -
Show answer
Waves travel slower in it, so its wavelength is shorter
Energy travels more slowly in a feedline than in free space, so the wavelength there is shorter by the velocity factor: 0,5 to 0,8 for coax, close to 1 for open-wire line. Faster waves would need a longer line.
Try it: Feedline Electrical Length -
Show answer
The diameter of its wires and the spacing between them
A balanced line’s characteristic impedance depends on its geometry, the ratio between wire diameter and spacing, so open-wire and ladder line can be tailored, typically 300 to 600 Ω. Its length has no effect on it.
-
Show answer
They must be kept well clear of nearby metal
Balanced feeders are cheap and low-loss, but they interact with their surroundings, so they must be kept away from window frames, fences and other metal. Coax keeps its field inside the screen and can run near metal.
-
Show answer
They would be far too large at HF wavelengths
A waveguide is a hollow tube, usually rectangular, that must be large compared with the wavelength, so it suits microwaves but not HF or even VHF. It handles very high power with low loss.
-
Show answer
On long runs and at high frequencies
Coax loss grows with length and with frequency, so a long run at VHF or UHF can waste much of the power. Short runs at HF lose little.
Try it: Feedline Loss -
Show answer
A low SWR, close to 1:1
SWR shows how well the antenna matches the line: with a good match little power is reflected and the SWR is near 1:1. SWR is never below 1:1, and a mismatch raises it.
Try it: SWR / VSWR & Return Loss -
Show answer
When the load impedance equals the source impedance
Maximum power transfer occurs when the load matches the source impedance, which is why transmitter, feedline and antenna should all have the same impedance. A very low load draws heavy current but has little voltage across it.
Try it: SWR / VSWR & Return Loss -
Show answer
3,5:1
For a resistive load, SWR is the larger impedance over the smaller: 175 ÷ 50 = 3,5:1. Dividing the 125 Ω difference by 50 Ω gives 2,5:1, which is not how SWR is defined.
Try it: SWR / VSWR & Return Loss -
Show answer
Better than 1,5:1 is acceptable; 2:1 can be tolerated
Better than 1,5:1 is fine for most purposes, and up to 2:1 is generally tolerable. Higher SWR calls for caution: it can break down feedlines, damage the transmitter and cause interference.
Try it: SWR / VSWR & Return Loss -
Show answer
Most transmitters cut their power to protect themselves
Reflected power can damage a transmitter, so most transmitters reduce their output when the SWR is high, and feedline loss may waste some of the reflected energy. The antenna does not radiate it backwards.
-
Show answer
The reflection coefficient, expressed in dB
Engineers usually quote the reflection, as a reflection coefficient or, in dB, as return loss; its implications are exactly the same as those of SWR. Velocity factor concerns the speed of waves in a feedline.
Try it: SWR / VSWR & Return Loss -
Show answer
It links a balanced load to unbalanced coax
Balun stands for balanced-to-unbalanced: a transformer between a balanced load, such as a dipole, and unbalanced coax. It can be made from coax (the bazooka), a wire transformer on a toroid, or ferrite rings over the cable.
Try it: DIY Baluns & Ununs -
Show answer
To keep current off the outside of the screen
A dipole is balanced but coax is not, so current tends to run along the outer surface of the screen, causing interference or picking it up. The balun prevents this; a 1:1 balun changes no impedance.
Try it: DIY Baluns & Ununs -
Show answer
4:1
The impedance ratio is 200 ÷ 50 = 4, so a 4:1 balun; its windings have a 2:1 turns ratio, since impedance follows the square of the turns ratio (chapter 14). Quoting 2:1 for the impedance mixes the two up.
Try it: DIY Baluns & Ununs -
Show answer
To match the antenna system to the radio’s 50 Ω
An ATU, also called an antenna coupler or Transmatch, transforms whatever impedance the antenna system presents into the 50 Ω the radio wants. Fitted at the radio, it leaves the antenna and its feedline mismatched.
Try it: L-network Matching -
Show answer
A lowpass filter
With the coil in series and the capacitors shunting high frequencies to ground, it passes low frequencies: a lowpass filter that also cuts harmonics, a typical transmitter output network. A series capacitor with coils to ground would make it highpass.
Try it: Low-pass Filter Designer -
Show answer
At the antenna, or fed through open-wire line
With the ATU in the shack, the coax to a mismatched antenna still carries a high SWR, and a long run then wastes much of the power. Mount the ATU at the antenna or feed it with open-wire line.
Try it: Feedline Loss -
Show answer
Into the 21 MHz dipole
At 21 MHz only the 21 MHz dipole presents a low, purely resistive impedance; the others present high impedances and take little power. That is why each band needs one, and only one, low-impedance element.
Try it: Half-wave Dipole -
Show answer
Four
The inner section works on the highest band and each further pair of traps adds one band, so three pairs give four bands. Each trap adds some loss, so many-band trap antennas are less efficient on the lower bands.
Try it: Half-wave Dipole -
Show answer
As low impedances, so the whole length works
A trap, a parallel tuned circuit, is a high impedance only near its resonance, on 40 m. On 80 m it acts as an inductor, so the whole antenna works and is shorter than a plain 80 m dipole.
Try it: Half-wave Dipole -
Show answer
21,3 MHz
Open-ended antennas such as dipoles resonate on odd harmonics: 3 × 7,1 = 21,3 MHz, in the 15 m band. On the even harmonic, 14,2 MHz, a dipole’s feed impedance is very high; only full-wave loops resonate on all harmonics.
Try it: Half-wave Dipole -
Show answer
Each dipole suits a different frequency; the nearest to resonance drives
Its dipoles, all fed from one feedline, are cut for different frequencies; at any frequency the one near resonance drives, longer ones reflect and shorter ones direct. The length ratio sets the range, 10:1 or more.
-
Show answer
The ratio of its longest dipole to its shortest
The range follows the ratio between the longest and shortest dipoles and can reach 10:1 or more; the manual’s wire LPA covers about 3:1. Few amateurs need this, as single-band antennas do better on our few bands.
-
Show answer
Antennas
All three are antennas: the log-periodic dipole array, the Marconi (a quarter-wave vertical fed against ground) and the rhombic, a large wire antenna fed with open-wire line.
-
Show answer
38 m
Each leg is a free-space quarter wave less about 5%: 300 ÷ 3,7 ÷ 4 × 0,95 = 19,26 m, so the dipole is 38,5 m, nearest 38 m. Skipping the 5% reduction gives 40,5 m, nearer 41 m.
Try it: Half-wave Dipole -
Show answer
About 10% at each end, in case it resonates elsewhere
Leave about 10% spare at each end, wrapped back on itself, so the dipole can be lengthened or shortened once it is up. At HF accuracy is not critical: a few millimetres will hardly be noticed.
-
Show answer
To choke off current on the outside of the braid
The coil forms a choke that reduces current on the outside of the braid, doing a balun’s job; a coil diameter about ten times the cable’s avoids damaging it. It adds nothing to the dipole’s resonance.
Try it: DIY Baluns & Ununs
Sign up free to save your score and see your progress in every chapter. You do not need to be a club member.