UTC 19:15:09 SAST 21:15 SFI 122 Kp 1 20 M GOOD 10 M FAIR 145.650 · 438.650 · 438.200 · 438.300 · 439.175
RAE practice questions

RAE mock exam

A practice run of the Radio Amateur Examination. Every time you open this page, a new exam is drawn from the questions of all the chapters and mixed, in the exam’s two papers.

Paper 1, regulations and operating procedures: 40 questions, 60 minutes. Paper 2, technical: 60 questions, 120 minutes. To pass you need at least 50% in each paper and 65% overall. Answer every question, then press Finish and mark: nothing is marked before that, as in the real exam.

Paper 1: Regulations and operating procedures

  1. 1. According to the manual, how are amateur satellites developed?
    Show answer

    By non-profit collaborations among amateurs

    Amateur satellites are designed and built by amateurs working together as a cooperative, non-profit effort.

    From Chapter 1: Overview of Amateur Radio
  2. 2. On 40 m CW the other station sends 'QSY 7090'. What should you do?
    Show answer

    Move with them to 7090 kHz

    QSY means 'change frequency to', and the figure that follows is the new frequency in kHz, not an offset in Hz.

    From Chapter 2: Operating Procedures Try it: Q Codes
  3. 3. Which of the following is a digital mode used in amateur radio?
    Show answer

    PSK

    PSK is a digital (data) mode, while FM, SSB and AM are phone modes that carry the human voice.

    From Chapter 1: Overview of Amateur Radio
  4. 4. As a new amateur you hear regulars using ham slang and pet phrases. What should you do?
    Show answer

    Say things in ordinary words that everyone understands

    The aim is clear communication, so speak plainly; slang meant to keep outsiders guessing only confuses other amateurs too.

    From Chapter 2: Operating Procedures
  5. 5. How is the word 'AXIS' spelt in the phonetic alphabet?
    Show answer

    Alpha X-ray India Sierra

    A is Alpha, X is X-ray, I is India and S is Sierra; Italy, Italia, Able, Item and Sugar are not in today's alphabet.

    From Chapter 2: Operating Procedures Try it: Phonetic Alphabet
  6. 6. You have called CQ a few times without any reply. What is the most sensible thing to do?
    Show answer

    Listen around the band for activity, then try a few more calls

    No reply often means poor propagation, so first listen for other activity; hopping across the band and calling without listening only spreads your calls about.

    From Chapter 2: Operating Procedures
  7. 7. Besides handling real emergencies, what do Hamnet members do?
    Show answer

    Train regularly and support community events

    Hamnet coordinates amateur emergency communications under the SARL, and its members train together and provide radio links at events such as marathons and rallies.

    From Chapter 2: Operating Procedures
  8. 8. A rare DX station ends its call with 'up five'. What does that mean?
    Show answer

    It is listening 5 kHz above its own transmit frequency

    Working split, the DX station listens 5 kHz above where it transmits, so you transmit there while you keep listening on its frequency.

    From Chapter 2: Operating Procedures
  9. 9. Which organisation does the ITU recognise as representing radio amateurs worldwide?
    Show answer

    IARU

    The IARU was formed to be the voice of radio amateurs internationally, and the ITU recognises it as their representative at its conferences.

    From Chapter 1: Overview of Amateur Radio Try it: ITU Radio Regulations Explained
  10. 10. Which of these is NOT recommended for a QSL card?
    Show answer

    QSO details split across both sides

    The QSO side must carry all the contact details so the card never needs turning over; the standard size, the card stock and a block layout are all recommended.

    From Chapter 2: Operating Procedures
  11. 11. Every amateur callsign has a prefix and a suffix. What does the suffix normally identify?
    Show answer

    The individual station

    The suffix, such as AN in ZS1AN, picks out the individual station; the area it operates from is shown by the prefix.

    From Chapter 2: Operating Procedures Try it: Callsign Lookup
  12. 12. Which of these words is NOT part of the international phonetic alphabet?
    Show answer

    Mexico

    M is Mike, so Mexico is not in the alphabet, although some place names, such as Quebec, are; Tango and Kilo are the standard words for T and K.

    From Chapter 2: Operating Procedures Try it: Phonetic Alphabet
  13. 13. Which band plans do South African amateurs follow?
    Show answer

    The IARU Region 1 plans, shared with Europe

    Africa lies in ITU Region 1 together with Europe, and IARU band plans normally cover a whole region, so South Africa keeps to the Region 1 plans.

    From Chapter 2: Operating Procedures Try it: Band Plans
  14. 14. What kind of organisation is the SARL?
    Show answer

    A non-profit representing amateurs

    The SARL is a non-profit association of amateurs that represents them nationally and internationally; it is not a government body.

    From Chapter 1: Overview of Amateur Radio
  15. 15. On a repeater, why should you leave a short gap before starting your over?
    Show answer

    So that anyone waiting gets a chance to call in

    The short gap between overs gives anyone else a chance to call in and join the conversation; it is courtesy, not a licence condition.

    From Chapter 2: Operating Procedures
  16. 16. What is a QSO in amateur radio?
    Show answer

    A contact between two amateur radio operators

    QSO is the Q-code term for a contact between two amateur stations.

    From Chapter 1: Overview of Amateur Radio Try it: Q Codes
  17. 17. What certificate is awarded for passing the practical examination?
    Show answer

    Radio Operator's Certificate

    Passing the practical assessment earns the Radio Operator's Certificate that ICASA requires; the HAREC comes from the written RAE.

    From Chapter 1: Overview of Amateur Radio
  18. 18. On an HF phone frequency you hear only a station's callsign, then silence. What should you do?
    Show answer

    Keep listening until you know what is going on

    A lone callsign tells you almost nothing, so keep listening until you understand what is happening; QRZ? asks who is calling you, and nobody has.

    From Chapter 2: Operating Procedures Try it: Q Codes
  19. 19. An off-road party is travelling through an uninhabited area. How can amateur radio help them?
    Show answer

    By linking the vehicles, reaching a home base and calling for help if needed

    In empty country, amateur radio keeps the vehicles of a party in touch, links them to a home base and can summon help in an emergency.

    From Chapter 1: Overview of Amateur Radio
  20. 20. ZS6XYZ wants to call CQ DX in Morse. Which of these calls is correctly sent?
    Show answer

    CQ DX CQ DX de ZS6XYZ ZS6XYZ K

    In Morse, 'de' comes before your own callsign and K invites any station to reply, whereas KN invites only a station already called; phonetics are never sent.

    From Chapter 2: Operating Procedures Try it: Abbreviations
  21. 21. What is the Logbook of The World (LoTW)?
    Show answer

    An online contact confirmation system

    LoTW is the ARRL's online system that matches uploaded logs from both stations to confirm contacts electronically.

    From Chapter 1: Overview of Amateur Radio Try it: Logbook & ADIF
  22. 22. What does the Q code QRP mean, as in 'a QRP station'?
    Show answer

    Decrease power, so a QRP station runs low power

    QRP means 'decrease power', so a QRP station is a low-power one, normally running no more than 5 W PEP, rather than a high-power one.

    From Chapter 2: Operating Procedures Try it: Q Codes
  23. 23. What callsign prefix is used for entry-level Class B licences in South Africa?
    Show answer

    ZU

    ZU callsigns identify the entry-level Class B licence; ZR and ZS callsigns are used for Class A.

    From Chapter 1: Overview of Amateur Radio Try it: Callsign Lookup
  24. 24. What happens to a Class B licence when the holder turns 25?
    Show answer

    It lapses

    A Class B (ZU) licence lapses on the holder's 25th birthday, so holders are encouraged to upgrade to Class A before then.

    From Chapter 1: Overview of Amateur Radio
  25. 25. According to the manual, how long can an amateur radio contest run?
    Show answer

    From about an hour up to 48 hours or more

    Contests last a set period, as short as an hour or two or as long as 48 hours or more, so a 12-hour limit is too short for the longest ones.

    From Chapter 1: Overview of Amateur Radio
  26. 26. You want to talk through your local 2 m repeater. Which mode must your radio use?
    Show answer

    FM

    Repeaters carry local FM voice traffic, so your radio must be set to FM to work through one.

    From Chapter 2: Operating Procedures
  27. 27. Two stations are chatting on CW about antennas and you would like to join them. What is the best approach?
    Show answer

    Follow the talk for a while, and call in only if you have something to add

    Listen to learn what is being discussed and join only if you can add something useful to that topic; steering the talk elsewhere hijacks their conversation.

    From Chapter 2: Operating Procedures
  28. 28. Which amateur radio activity might require batteries and portable operation from a remote site?
    Show answer

    RaDAR

    RaDAR (Rapid-Deployment Amateur Radio) means carrying a radio, antenna and battery power into the field and setting up quickly anywhere.

    From Chapter 1: Overview of Amateur Radio
  29. 29. What do amateurs call a trip to operate a station from a rare country or island?
    Show answer

    DXpedition

    A DXpedition is a trip to a rare or unusual place to set up and operate a station that many others want to contact.

    From Chapter 1: Overview of Amateur Radio
  30. 30. In which of the ITU's radio regions does South Africa lie?
    Show answer

    Region 1

    South Africa, like the rest of Africa and Europe, is in ITU Region 1 and so follows the IARU Region 1 band plans.

    From Chapter 1: Overview of Amateur Radio Try it: ITU Radio Regulations Explained
  31. 31. What is a typical simple project an amateur might build?
    Show answer

    A soundcard interface

    A soundcard interface for a computer is simple enough to build in a single evening.

    From Chapter 1: Overview of Amateur Radio
  32. 32. A contact is made at 01:30B (SAST) on 5 March. What is the date and time in UTC?
    Show answer

    23:30Z on 4 March

    SAST is two hours ahead of UTC, so going back two hours from 01:30B crosses midnight and gives 23:30Z on the previous day, 4 March.

    From Chapter 2: Operating Procedures Try it: UTC Clock & Timers
  33. 33. How many multiple-choice questions are in RAE Paper 1? (Indicative: the format given in the SARL's 2024 manual, which the SARL can change.)
    Show answer

    40

    Paper 1 (general, operating procedures and regulations) has 40 multiple-choice questions and the technical Paper 2 has 60, but check the SARL's RAE page for the current format.

    From Chapter 1: Overview of Amateur Radio
  34. 34. What is SA-QSL?
    Show answer

    The SARL's free electronic confirmation service

    SA-QSL confirms contacts electronically and is free to SARL members, and its matched contacts count towards the Worked All ZS awards; no cards are printed.

    From Chapter 2: Operating Procedures
  35. 35. What attitude should an amateur have towards beginners?
    Show answer

    Helpful and friendly

    The Code of Conduct says the amateur is friendly, giving patient help, advice and encouragement to beginners.

    From Chapter 1: Overview of Amateur Radio
  36. 36. Which group coordinates amateur emergency communications in South Africa?
    Show answer

    Hamnet

    Hamnet is the SARL group that organises amateur emergency communications in South Africa.

    From Chapter 1: Overview of Amateur Radio
  37. 37. With the stressed syllable in capitals, which pair is right for the phonetic words for P and J?
    Show answer

    pa-PA and ju-li-ETT

    The manual's table gives Papa and Juliett, stressing the second syllable of Papa and the last of Juliett: pa-PA and ju-li-ETT.

    From Chapter 2: Operating Procedures Try it: Phonetic Alphabet
  38. 38. Someone on the repeater asks how their signal is reaching you. What kind of report should you give?
    Show answer

    Describe it: 'loud and clear', 'some hiss' and so on

    You hear only the repeater's output, which tells you little about their signal into it, so describe what you hear in words, not numbers.

    From Chapter 2: Operating Procedures
  39. 39. Which of these is one of ICASA's functions?
    Show answer

    Setting the conditions attached to radio licences

    ICASA makes regulations, imposes licence conditions and manages the spectrum in South Africa; amateur emergency communications are coordinated by Hamnet.

    From Chapter 1: Overview of Amateur Radio
  40. 40. Why may an amateur station NOT be used as a community radio station?
    Show answer

    Amateur radio is for direct communication between amateurs, not broadcasting

    Broadcasting is not allowed: amateur radio is for communication between amateurs, not a service for the general public.

    From Chapter 1: Overview of Amateur Radio Try it: ITU Radio Regulations Explained

Paper 2: Technical

  1. 1. Which is nearest to the wavelength of an 18,1 MHz signal?
    Show answer

    17 m

    λ = 300 ÷ F = 300 ÷ 18,1 = 16,6 m, nearest 17 m, inside the 17 m band. 1,7 m has the decimal comma one place out, a power of ten.

    From Chapter 8: Alternating Current Try it: Frequency ↔ Wavelength
  2. 2. You want a linear amplifier to give at most 500 W PEP. With a two-tone signal applied, which is nearest to the true average power the wattmeter should show when the drive is set?
    Show answer

    240 W

    With two tones PEP is twice the average: 500 ÷ 2 = 250 W, so 240 W is nearest and keeps the PEP under 500 W. Dividing by 1,414 gives 354 W and would overdrive it.

    From Chapter 29: Measurements Try it: dBm, Watts & dB
  3. 3. A PNP transistor’s base is held at exactly the same voltage as its emitter, with its collector negative. How much collector current flows?
    Show answer

    Practically none

    A PNP transistor needs its base about 600 mV negative of its emitter before base current, and so collector current, can flow; with no voltage between them it is shut off, as an NPN would be.

    From Chapter 17: The Bipolar Junction Transistor
  4. 4. A tuned circuit at 3,5 MHz uses a 150 pF capacitor, and its total loss resistance is 3 Ω. Which is nearest to its Q?
    Show answer

    100

    XC = 1 ÷ (2π × 3,5 × 10⁶ × 150 × 10⁻¹²) = 303 Ω, so Q = XC ÷ R = 303 ÷ 3 = 101, nearest 100. Leaving out the 2π makes the Q 2π times too high, about 630.

    From Chapter 11: Tuned Circuits Try it: Reactance & Resonance
  5. 5. Capacitors of 1,5 nF, 3,3 nF and 6,8 nF are connected in parallel. What is their total capacitance?
    Show answer

    11,6 nF

    In parallel the values add: 1,5 + 3,3 + 6,8 = 11,6 nF. About 0,9 nF, less than the smallest of them, is what the rule for capacitors in series gives.

    From Chapter 9: Capacitance and the Capacitor Try it: Components: Colour Codes & Values
  6. 6. Why is the gain of a direct-conversion receiver’s RF amplifier usually kept low?
    Show answer

    So that strong signals cannot overload the mixer

    A strong signal easily overloads a mixer, causing intermodulation distortion, so little gain goes ahead of it and most is placed at audio, after the lowpass filter. Low RF gain does not lower the receiver’s noise.

    From Chapter 23: Receiver Fundamentals
  7. 7. A 36 W lamp runs from a 48 V RMS sine supply. What RMS current does it draw?
    Show answer

    0,75 A

    I = P ÷ V = 36 ÷ 48 = 0,75 A, an RMS current, as the power formulas work with RMS values. 1,06 A is the peak current, 1,414 times larger; 48 ÷ 36 = 1,33 divides the wrong way.

    From Chapter 8: Alternating Current Try it: Ohm's Law & Power
  8. 8. What is a link budget?
    Show answer

    A tally of power, gains and losses, to judge if the path will work

    A link budget adds up transmitter power, antenna gains, feeder and other losses and the path loss to predict the received signal, and so whether a link is feasible. Path loss alone is just one entry.

    From Chapter 27: Propagation Try it: Link Budget & Path Loss
  9. 9. If the current is 0,86 A and the resistance is 73 Ω, what is the voltage?
    Show answer

    62,78 V

    V = I × R = 0,86 A × 73 Ω = 62,78 V; 6,278 V and 627,8 V put the decimal comma one place out, and 84,88 V divides 73 by 0,86 instead of multiplying.

    From Chapter 4: Resistance and Ohm’s Law Try it: Ohm's Law & Power
  10. 10. Why does a very weak FM signal come with hiss in the audio?
    Show answer

    The limiter cannot yet hold the level steady

    A weak signal is too small for the limiter to clip, so its amplitude noise reaches the discriminator and is heard as hiss. As the signal strengthens the limiter takes over and the hiss fades.

    From Chapter 24: The Superheterodyne Receiver
  11. 11. What is the main purpose of the RF amplifier stage in a receiver?
    Show answer

    To make the receiver more sensitive

    The RF stage lifts the weak signals from the antenna so that fainter stations can be heard: it improves sensitivity. Selectivity comes mainly from filters and bandwidth, though tuned circuits around the stage help a little.

    From Chapter 23: Receiver Fundamentals
  12. 12. When do the losses in coaxial cable become large?
    Show answer

    On long runs and at high frequencies

    Coax loss grows with length and with frequency, so a long run at VHF or UHF can waste much of the power. Short runs at HF lose little.

    From Chapter 26: Antennas Try it: Feedline Loss
  13. 13. A 7 MHz oscillator is 60 Hz above its marked frequency, and its output is tripled to 21 MHz. How far off is the 21 MHz signal?
    Show answer

    180 Hz

    A multiplier multiplies every frequency it is fed, so a 60 Hz error at 7 MHz becomes 3 × 60 = 180 Hz at 21 MHz. The error is not left at 60 Hz; it grows with the multiplication factor.

    From Chapter 20: Frequency Translation
  14. 14. Take the body’s resistance from one hand to the other as 1 500 Ω. What voltage across that path would drive the 20 mA the manual warns about?
    Show answer

    30 V

    V = I × R = 0,02 A × 1 500 Ω = 30 V, so a voltage far below the mains can be dangerous, especially through wet skin. Dividing 1 500 by 20 (giving 75) turns Ohm’s law upside down.

    From Chapter 32: Safety Considerations Try it: Ohm's Law & Power
  15. 15. What produces thermal noise?
    Show answer

    The random motion of electrons caused by heat

    Heat keeps the electrons in every conductor moving at random, and that motion is thermal noise; it is present even with no current flowing. Heat flowing away into the air makes no electrical noise.

    From Chapter 19: The Oscillator
  16. 16. Which option is nearest to a power ratio of 0,07 expressed in decibels?
    Show answer

    −12 dB

    10 log₁₀ 0,07 = −11,5 dB, between −13 dB for 0,05 and −10 dB for 0,1, so −12 dB is nearest; 20 log 0,07 would give about −23 dB.

    From Chapter 12: Decibel Notation Try it: dBm, Watts & dB
  17. 17. For safety, what should the exposed metal parts in a station, such as equipment cases, be joined to?
    Show answer

    A good earth

    With the metal earthed, a fault sends a large current to earth and the fuse blows or the earth-leakage unit trips. Neutral carries the working current, and a broken or swapped neutral could leave the metal live.

    From Chapter 32: Safety Considerations
  18. 18. At roughly what voltage is a 12 V lead-acid battery normally charged?
    Show answer

    About 14 V

    To push charge in, the charger must sit a little above the battery’s nominal voltage, so a 12 V lead-acid battery is usually charged at about 14 V. At 12 V almost no charge would flow.

    From Chapter 16: The Power Supply
  19. 19. A superhet’s LO is on 5,100 0 MHz and its IF filter passes 9,000 3 to 9,003 0 MHz. What happens to a signal on 14,098 0 MHz?
    Show answer

    It mixes to 8,998 0 MHz and is rejected

    14,098 0 − 5,100 0 = 8,998 0 MHz, below the 9,000 3 MHz edge, so the IF filter rejects it. Landing on 9,002 0 MHz would need a signal on 14,102 0 MHz.

    From Chapter 24: The Superheterodyne Receiver
  20. 20. How do packet radio stations get messages through to stations beyond their own range?
    Show answer

    Other stations along the way relay the packets onward

    Packet frames hop through digipeaters and network nodes to stations out of direct range, much as the Internet passes data on. High power and big antennas are not how packet works.

    From Chapter 31: Digital Communication Modes
  21. 21. Why do many practical mixers switch one signal with the other, rather than truly multiplying the two?
    Show answer

    It is hard to multiply accurately without distortion

    Multiplying two sine waves accurately without adding distortion is hard, so switching mixers chop one signal with the other instead. It is the switching mixer, not true multiplication, that needs a strong LO.

    From Chapter 20: Frequency Translation
  22. 22. Which kind of power amplifier does the manual’s SSB transmitter use?
    Show answer

    A linear amplifier, probably in class AB

    An SSB signal’s amplitude follows the speech, so the PA must be linear; the manual suggests class AB, linear enough yet reasonably efficient. A class C stage would distort it into splatter and intermodulation.

    From Chapter 22: The Transmitter
  23. 23. Which value is the same as 0,0039 H?
    Show answer

    3,9 mH

    1 H = 1000 mH, so 0,0039 H × 1000 = 3,9 mH. 39 mH would be 0,039 H, ten times too much, and 3900 mH is 3,9 H.

    From Chapter 10: Inductance and the Inductor Try it: Unit Converter
  24. 24. Seen mathematically, AM multiplies the carrier by the audio signal with a DC offset added. Why does the result contain a component at the carrier frequency?
    Show answer

    The DC offset is 0 Hz, so its mixing products fall on the carrier frequency

    Mixing gives the sum and difference of the frequencies multiplied. The DC offset is 0 Hz, so both its products equal the carrier frequency; every audio frequency, however low, gives products offset from it.

    From Chapter 21: Modulation Methods
  25. 25. What does the term 'photo' mean in 'photovoltaic'?
    Show answer

    Light

    'Photo' means light, as in photograph, so photovoltaic cells turn light into electricity; 'solar' would mean 'of the sun'.

    From Chapter 3: Basic Electrical Concepts
  26. 26. According to the manual, what is the combined effect of the millions of switches in a city?
    Show answer

    They slowly raise the noise level, hampering radio across the city

    Each switch adds a little noise, and millions of them raise the urban noise level until radio communication across the city is hampered. Random bursts of noise add up; they do not cancel.

    From Chapter 28: Electromagnetic Compatibility
  27. 27. By the manual, how common is it for a modern amateur transmitter to include a receiver as well?
    Show answer

    Almost every one does, at least on its own transmit bands

    Because of these advantages, nearly all modern amateur transmitters can also receive, at least on their own bands, and many add general-coverage receive. Separate units were the rule only in the early days.

    From Chapter 25: Transceivers and Transverters
  28. 28. How does an IC voltage regulator manage to remove most of the ripple left on its input?
    Show answer

    It adjusts its resistance fast enough to cancel it

    The regulator adjusts its internal resistance continually, and fast enough to cancel the rise and fall of its input, so its output stays clean. Storing charge between peaks is how the smoothing capacitor works.

    From Chapter 16: The Power Supply
  29. 29. A 9 V battery drives 2 µA through a high-value resistor. What is its resistance?
    Show answer

    4,5 MΩ

    R = V ÷ I = 9 V ÷ 0,000 002 A = 4 500 000 Ω = 4,5 MΩ; 0,45 MΩ and 45 MΩ misplace the decimal comma, and 4,5 kΩ takes microamperes for milliamperes.

    From Chapter 4: Resistance and Ohm’s Law Try it: Ohm's Law & Power
  30. 30. A sine wave of 0,4 V peak is applied straight to the base of an unbiased class C stage like the manual’s. What output results?
    Show answer

    None: the transistor never conducts

    A silicon transistor needs about 600 mV across its base-emitter junction before it conducts, and 0,4 V never gets there, so no collector current flows. Class C needs a large input signal.

    From Chapter 18: The Transistor Amplifier
  31. 31. An antenna system is fed with 80 W but radiates only 52 W. What is its efficiency?
    Show answer

    65%

    η = POut ÷ PIn = 52 ÷ 80 = 0,65, and multiplying by 100% gives 65%. 35% is the share lost as heat, not the share radiated.

    From Chapter 7: Power in DC Circuits
  32. 32. Which power ratings does the manual give for metal film resistors?
    Show answer

    125 mW to 500 mW

    The manual gives metal film resistors 125 mW to 500 mW (larger ones exist, but are less common). Up to 2 W is the range of carbon film resistors, and high ratings belong to wirewound ones.

    From Chapter 5: The Resistor and Potentiometer
  33. 33. How does the manual say its simple SSB transmitter could be made into a low-level AM transmitter?
    Show answer

    Use an unbalanced modulator and a wider crystal filter

    An unbalanced modulator lets the carrier through, and a crystal filter wide enough for both sidebands passes the whole AM signal. The narrow filter would keep one sideband and reject the carrier just outside its passband.

    From Chapter 22: The Transmitter
  34. 34. Why does a meter movement need a rectifier before it can read AC?
    Show answer

    It is a DC instrument: AC would push its pointer each way in turn

    A moving-coil movement is designed for DC: its turning force follows the direction of the current, so on AC the pointer barely moves. AC flows through the coil easily; the pointer simply cannot follow it.

    From Chapter 29: Measurements
  35. 35. Two 220 pF capacitors are connected in series. What is the size of their total reactance at 7 MHz?
    Show answer

    207 Ω

    Each XC = 1 ÷ (2π × 7 × 10⁶ × 220 × 10⁻¹²) = 103,3 Ω, and in series they add: 207 Ω, capacitive. Reading 220 pF as 22 pF gives ten times too much, 2,07 kΩ.

    From Chapter 11: Tuned Circuits Try it: Reactance & Resonance
  36. 36. An amplifier designed for a 600 Ω load is to drive a 15 Ω speaker through a transformer. What turns ratio makes the speaker look like 600 Ω to the amplifier?
    Show answer

    6,32:1

    The impedance ratio is 600 ÷ 15 = 40, and the turns ratio is its square root: √40 = 6,32, so 6,32:1. Using 40:1 as the turns ratio would transform the impedance 1 600 times.

    From Chapter 14: The Transformer Try it: DIY Components
  37. 37. A filter is fed with a signal of +10 dBm, and −60 dBm comes out. What is its attenuation?
    Show answer

    70 dB

    Both levels are referred to 1 mW, so the attenuation is their difference, +10 − (−60) = 70 dB; adding them, 10 + (−60) = −50, gives the wrong 50 dB.

    From Chapter 13: Filters Try it: dBm, Watts & dB
  38. 38. An operator turns up the drive until an SSB linear amplifier is working well beyond its rating. What will other stations most likely notice?
    Show answer

    Splatter caused by intermodulation products

    Driven too hard, a linear amplifier flattens the peaks, and the speech frequencies mix into intermodulation products close to the signal, widening it into splatter. Harmonics appear too, but far away, where the output filter deals with them.

    From Chapter 28: Electromagnetic Compatibility
  39. 39. In a potentiometer, what does the position of the wiper determine?
    Show answer

    The resistance from it to each end of the track

    Moving the wiper changes the resistance from the wiper to each end, but the two always add up to the fixed end-to-end value, which the wiper cannot change.

    From Chapter 5: The Resistor and Potentiometer
  40. 40. According to the manual, what does an alternating magnetic field set up?
    Show answer

    A changing electric field

    By induction, an alternating magnetic field sets up a changing electric field, which in turn sets up a changing magnetic field, and so on: together they form an electromagnetic wave. An alternating field cannot induce a steady one.

    From Chapter 26: Antennas
  41. 41. In an inductor fed with AC, which reaches its peak first?
    Show answer

    The voltage across the coil

    The voltage leads, so it peaks first and the current follows a quarter of a cycle later. In a capacitor it is the other way round: the current peaks first.

    From Chapter 10: Inductance and the Inductor
  42. 42. What is a hole in a semiconductor crystal?
    Show answer

    A place where an electron should be but is missing

    A hole is a gap in the bonds of the crystal where an electron ought to be; it acts like a positive charge. A free electron, not bound into the crystal, is the other kind of carrier, in N-type material.

    From Chapter 15: Semiconductors and the Diode
  43. 43. In the circuit symbol for a battery, what does the longer line stand for?
    Show answer

    The positive terminal

    In the battery symbol the long line always marks the positive terminal and the short line the negative one; the manual adds a '+' beside it only to make that plain.

    From Chapter 6: Direct Current Circuits
  44. 44. What does APRS provide?
    Show answer

    Real-time tracking of mobile stations by GPS

    APRS (Automatic Position Reporting System) sends position reports, usually from a GPS receiver, so stations can be followed on a map in real time. It does not report propagation.

    From Chapter 31: Digital Communication Modes
  45. 45. Electric potential is similar to what in water systems?
    Show answer

    Pressure

    Voltage is like water pressure: the higher it is, the more flow it pushes through the pipe, and that rate of flow is what matches the current.

    From Chapter 3: Basic Electrical Concepts
  46. 46. What other name does the manual give the Clapp oscillator?
    Show answer

    The series-tuned Colpitts

    In the Clapp the tuning capacitance sits in series with the coil, so the manual calls it a series-tuned Colpitts; its VCO and crystal circuits both use it. The ordinary Colpitts has a parallel tuned circuit.

    From Chapter 19: The Oscillator
  47. 47. A 2 m transverter has a 116 MHz LO. On transmit its transceiver sends USB on 29,350 MHz. What goes out?
    Show answer

    145,350 MHz, USB

    The transmit mixer keeps the sum, 116 + 29,350 = 145,350 MHz, and a sum keeps the sideband the right way round: still USB. Only LO minus drive, like the rejected 86,650 MHz product, would invert it.

    From Chapter 25: Transceivers and Transverters
  48. 48. Why is QO-100 an easy satellite to work, once a station has the right equipment?
    Show answer

    It is geostationary, so a fixed dish sees it at any hour

    QO-100 is geostationary, staying put in the sky, so a fixed dish of about 800 mm works it at any hour. It needs microwave equipment, not 2 m FM.

    From Chapter 27: Propagation
  49. 49. Which advantage of CW does the manual point out?
    Show answer

    It can be understood at far lower signal levels than voice

    CW stays readable at signal levels far below what voice needs: about 13 dB less power than SSB. It does need a beat-frequency oscillator (or product detector) in the receiver to be heard as a tone.

    From Chapter 21: Modulation Methods
  50. 50. When can an emitter follower provide power gain, according to the manual?
    Show answer

    When it delivers more current than it takes from its source

    Its voltage gain is only about 1, but power is V × I, so it gives power gain whenever its output current exceeds its input current, which it easily does. Drawing more current than it delivers would be a loss.

    From Chapter 18: The Transistor Amplifier
  51. 51. What does the manual mean by a small-signal transistor?
    Show answer

    One designed for low-power work

    Small-signal transistors are the ordinary types designed for low-power work, such as amplifying weak signals, and their β is typically 100 to 500. Switching large currents calls for bigger power transistors.

    From Chapter 17: The Bipolar Junction Transistor
  52. 52. Why does the manual's home-made dummy load have a resistance of 50 Ω?
    Show answer

    Most amateur transceivers are designed to work into it

    A dummy load stands in for the antenna, so it must present the resistance the transmitter expects: 50 Ω for most amateur transceivers. Fifty 2,5 kΩ resistors happen to give 50 Ω; the count alone does not set it.

    From Chapter 6: Direct Current Circuits Try it: DIY Components
  53. 53. The inductor in a lowpass filter has a reactance of 40 Ω at 10 MHz. What is its reactance at 20 MHz?
    Show answer

    80 Ω

    XL = 2πfL is proportional to frequency, so doubling f doubles XL to 80 Ω; halving it to 20 Ω is what a capacitor’s reactance would do.

    From Chapter 13: Filters Try it: Reactance & Resonance
  54. 54. In the manual’s varicap circuit, the bias voltage reaches the diode through an inductor, L1. What is L1 for?
    Show answer

    It passes the DC bias but blocks the RF signal

    L1 has a high reactance at the signal frequency, so RF cannot leak into the bias supply, which would add losses and lower the Q, while the DC bias passes freely. Passing RF and blocking DC is what C1 does.

    From Chapter 15: Semiconductors and the Diode Try it: Reactance & Resonance
  55. 55. Fourier first devised his transform for continuous signals. Which variant is used for sampled signals?
    Show answer

    The discrete Fourier transform, or DFT

    For sampled signals DSP uses the discrete Fourier transform, which takes a block of N samples and shows which sine frequencies it contains. The FFT is simply a fast way of computing it.

    From Chapter 30: Digital Systems
  56. 56. A step-down transformer is feeding a load. Which of its windings carries the larger current?
    Show answer

    The secondary winding

    Current changes the opposite way to voltage. A step-down transformer lowers the voltage, so its secondary carries the larger current: a 10:1 transformer drawing 1 A from the supply gives 10 A to the load.

    From Chapter 14: The Transformer
  57. 57. Compared with the current through it, how does the voltage across a capacitor behave in time?
    Show answer

    It lags behind the current

    Because the current in a capacitor leads, the voltage lags behind it, peaking a quarter of a cycle later. Saying the voltage leads puts the two the wrong way round.

    From Chapter 9: Capacitance and the Capacitor
  58. 58. A lightning stroke briefly carries 30 kA while 200 MV appears across its path. What is the peak power?
    Show answer

    6 × 10¹² W

    P = V × I = (200 × 10⁶ V) × (30 × 10³ A) = 6000 × 10⁹ = 6 × 10¹² W. 6 × 10⁹ W takes the 30 kA as 30 A, leaving out the kilo.

    From Chapter 7: Power in DC Circuits Try it: Ohm's Law & Power
  59. 59. A device leaves the power of a signal exactly unchanged. What is its gain in decibels?
    Show answer

    0 dB

    A ratio of 1 is 10 log₁₀ 1 = 0 dB, and adding 0 dB to a chain changes nothing, just as multiplying by 1 changes nothing.

    From Chapter 12: Decibel Notation
  60. 60. What is a NAND gate?
    Show answer

    An AND gate followed by a NOT gate

    A NAND puts the output of an AND gate through a NOT, so its output is 0 only when all its inputs are 1. A NOT on just one input makes a different gate altogether.

    From Chapter 30: Digital Systems